Pair of triangular side panels with fixings to fit all Tonti frame models with slotted side panel lugs under the seat

This is a kit, the fixings need bending and glueing to the sidepanel before the side panels can be fitted. The panels are GRP, fitting instructions are provided in German

 This part is available by special order, request a quote

Complete electronic ignition kit containing alternator mounted ignition pickup, fittings and amplifier unit. Works with standard 3 Ohm 12 volt coils and can be used to replace points or Motoplat ignition on models with Saprisa charging systems. The pickups for this kit are mounted on the alternator stator. Supplied with instructions in German with wiring diagrams.

2 year warranty on Sachse ignition kits

Eliminates vague timing due to worn distributors on big twins. Preloaded with nine ignition curves, two of which are designed for twin plugged bikes. Once fitted no further adjustment should be necessary. See this link for fitting instructions. Note that if you are replacing a Digiplex system you will also need to replace your 'square' coils with higher impedance 12 volt coils e.g. ELA31165

 This part is available by special order, request a quote

Complete single disc clutch kit for 5 speed big twins containing flywheel, new deep spline clutch hub, friction plate, spring plate, pressure plate, and flywheel bolts. Suitable for all big twins with either distributor or crankshaft mounted ignition system, not suitable for Digiplex equipped models.

This clutch upgrade has the following advanges over the old two plate clutch:

• Reduction in flywheel and clutch weight of approx. 1KG
• Improved acceleration
• Smoother gear changes at high RPM
• Quicker engine decelleration
• Reduction in engine vibration as the clutch assembly is (this is not possible with the original clutch)
• Lighter handlebar clutch lever action
• More precise clutch engagement and disengagement.
• More progressive clutch engagement.
• Increased ability to handle higher torque and horsepower.
• Lower clutch disk wear (reduced maintenance)
• Fewer parts (no intermediate plate, no second friction plate) to wear out
• Ease of assembly - gearbox can be fitted to engine without centering of the clutch disk.

 This part is due back in stock soon, call 01484 841395 to reserve yours

Gorgeous polished aluminium reservoir cap for PS15 Brembo master cylinder fitted to rear linked system on many models, will fit front master cylinder on models where a PS15 handlebar master cylinder is fitted. Seal is not included with this cap - you should re-use your original cap seal

Make your Guzzi stand out from the crowd!

 This part is available by special order, request a quote

 14661100 GU14661100 14 66 11 00
 1466 1100 1466.1100 14.66.11.00

Also fits Ducati 600 SL Pantah, Ducati 750/900 SS, Ducati 860/900 GTS, Ducati 900 Darmah, Ducati 900 MHR, Ducati 1000 MHR

Lightweight 5mm battery plate in a silver finish, supplied with countersunk M8 screws

This is an upgrade to the standard steel plate, perfect for your Tonti framed special (it will also fit Cali 1100 and Cali EV based specials. On some models you may need to enlarge the cut out for the speedo cable

 Availability varies on this part, check availability

14418200-z 14418200 GU14418200 14 41 82 00
 1441 8200 1441.8200 14.41.82.00

Pair of adjustable Tommaselli clipons, quality aluminium castings and chrome plated tube

These clip ons pivot on the central bolt to adjust the handlebar angle, pull back angle is adjusted on the fork stanchion clamp. These clip ons are unsuitable for use with the PS12 handlebar master cylinder. Bar ends are held in by a rivet and some modification will be needed if you wish to fit bar end mirrors.

 This part is available by special order, request a quote

Tough Xplorer top box / top case to match Hepco and Becker Xplorer panniers, ideal for enduro touring. Extremely endurable combination of black anodised aluminium sheet and coloured shock-resistant plastic.

• Completely waterproof thanks to special seals
• Made of 1.5 mm thick plate aluminum and highly
impact-resistant plastic molding
• Absorbs impacts and ground contact
• Stable metal locks, integrated carrying handles
• Case and top case available with simultaneous
locking (please specify when ordering)
• Takes a full-face helmet
• Innovative side hinged design
• Fits all H&B rear racks and aluminum racks

 This part is available by special order, request a quote

Black 55 litre Junior top box / top case to match Hepco and Becker Junior Flash panniers. This is the classic Hepco and Becker top box design. Sized to take two helmets

• Silver painted covers can be removed for colour matching to your bike
• Unbreakable, special double walled shell made of impact resistant plastic which absorbs bumps and falls
• Completely waterproof thanks to special seals
• Fitted with rugged metal locks and an ergonomic carry handle
• Aerodynamic design
• Racks and accessories available separately

This is a great value top case which are quickly and securely fitted to any Moto Guzzi. The discreet and classic styling looks right on any Guzzi from the 1970's to the present day. Supplied with two keys. See LUA70127 for a Guzzi badge to fit these panniers. This latches to any Hepco or Guzzi rack with a oblong section at the rear, e.g. LUA61051

 This part is available by special order, request a quote

Polished aluminium alternator cover

For big twins with Bosch charging systems only. Not deep enough for later bikes with Ducati or Saprisa. See ACA18650 for deeper version.

 This part is available by special order, request a quote

18001650-z 18001650 GU18001650 18 00 16 50
 1800 1650 1800.1650 18.00.16.50

Replacement clutch plate for single plate RAM clutches

Torque setting for fitting this is 25Nm with a thread locking compound

 This part is available by special order, request a quote